{
 "id": "us-uarizona-hp-air-receivers",
 "country": "United States",
 "language": "English",
 "buyer": "Arizona Board of Regents on behalf of the University of Arizona (Procurement and Contracting Services)",
 "project": "RFP L192302 High Pressure Air Receivers for the University's hypersonic wind tunnel facility, with Addendum 1",
 "year": "2022",
 "files": [
  {"file": "L192302_High_Pressure_Air_Receivers.pdf", "pages": 30, "text_layer": true, "what_it_is": "The RFP: statement of work, definitions, instructions to proposers, agreement terms and conditions (pp. 3-23), scope of work and technical requirements 5.0 (pp. 23-26; drawings on p. 25 are images), pricing and proposal data 5.6 (p. 26), certification forms (pp. 27-30)."},
  {"file": "L192302_Addendum_1.pdf", "pages": 5, "text_layer": true, "what_it_is": "Addendum 1: cover (p. 1), answers to four bidder questions (p. 2), and higher-resolution copies of the p. 25 drawings as images (p. 3 individual tank; pp. 4-5 alternative arrangements 2a with six tanks and 2b with twelve tanks)."}
 ],
 "quality": "Performance-style RFP (capacity, pressure, envelope) rather than a vessel design; the only geometry is in low-resolution image drawings, materials are not named, and the pricing page restates the design basis with different numbers (1164 ft3, 100 °F).",
 "read_by": "Mavlon, read from the documents with AI help before any run, November 2026",
 "items": [
  "High pressure compressed air receiver tanks (horizontal, saddle and leg supported) for a hypersonic wind tunnel: 1 to 12 vessels with at least 1150 ft3 total volume at 2000 psig; vendor chooses the configuration (examples: 6 tanks of 200 ft3 or 12 tanks of 97 ft3)",
  "Per vessel: saddles, leg plates and leg bases; 900# flanges with blinds, gaskets, nuts and studs; straight-thread O-ring forged steel plugs; nameplate and bracket; pressure gauge, drain valve and ASME-stamped pressure relief valve set for shipping; one spare gasket set"
 ],
 "checks": [
  {"n": 1, "area": "scope", "check": "What is being bought", "answer": "Design, manufacture and delivery of high pressure compressed air tanks to augment the University's hypersonic wind tunnel facility; tank size and configuration are open, and proposals are evaluated on delivery schedule, site preparation feasibility, manufacturer experience and cost.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Design, manufacture and deliver high pressure compressed air tanks to augment the University’s hypersonic wind tunnel facility."},
  {"n": 2, "area": "geometry", "check": "Required total capacity", "answer": "Minimum total capacity 1150 ft3 (section 5.2 and the drawing captions). The pricing page base proposal says minimum 1164 ft3 (see contradictions).", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Minimum Total Capacity 1150 FT3"},
  {"n": 3, "area": "geometry", "check": "Number of vessels and maximum length", "answer": "Minimum 1, maximum 12 vessels; maximum length 50 ft.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Number of vessels minimum 1, maximum 12"},
  {"n": 4, "area": "geometry", "check": "Overall envelope (changed by Addendum 1)", "answer": "Addendum 1 Q2 adds height and width limits: vessels or assemblies of multiple vessels on a structural frame no more than 50 ft long, 20 ft high, 15 ft wide; configurations within 30 ft long, 15 ft high, 12 ft wide are preferred. The 50 ft length limit is unchanged; the addendum is the governing statement of the envelope.", "evidence": "L192302_Addendum_1.pdf, p. 2", "quote": "maximum dimensions no more than 50’ long, 20’ high, 15’ wide."},
  {"n": 5, "area": "code", "check": "Construction code and stamp", "answer": "ASME BPVC Section VIII Division 1, constructed and stamped; the ASME-required nameplate and bracket are furnished and installed (5.2.4).", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Tanks to be in accordance with ASME Boiler and pressure vessel code section VIII D1, constructed and stamped."},
  {"n": 6, "area": "code", "check": "Division 2 option (Addendum 1)", "answer": "Addendum 1 Q1: the University will evaluate a voluntary ASME BPVC Section VIII Division 2 option. Division 1 stays the stated requirement ('all else remains the same').", "evidence": "L192302_Addendum_1.pdf, p. 2", "quote": "Yes- the University will evaluate a voluntary option for ASME BPVC Section viii, Div 2"},
  {"n": 7, "area": "design", "check": "Design pressure and MAWP", "answer": "Design pressure 2000 psig; MAWP 2000 psig at 120 °F.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Maximum Allowable Working Pressure 2000 PSIG at 120 F"},
  {"n": 8, "area": "design", "check": "Design temperature", "answer": "120 °F (section 5.2). The pricing page base proposal says 2000 psig at 100 °F (see contradictions).", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Design Temperature 120 F"},
  {"n": 9, "area": "design", "check": "MDMT", "answer": "0 °F (also 'mdmt 0 f' on the pricing page).", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "MDMT- Minimum Design Metal Temperature 0F"},
  {"n": 10, "area": "materials", "check": "Corrosion allowance", "answer": "0.0625 in.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Corrosion Allowance 0.0625”"},
  {"n": 11, "area": "materials", "check": "Shell and head material", "answer": "Not specified. The only material named is forged steel for the straight-thread O-ring sealed inlet, outlet and drain plugs. Searched the full text layer of both files (material, SA-, carbon, steel) and read the image drawings (RFP p. 25, Addendum pp. 3-5); none names a plate or forging grade.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Straight thread, O-ring sealed, forged steel inlet, outlet and drain plugs"},
  {"n": 12, "area": "nozzles", "check": "Nozzle arrangement and sizing rule", "answer": "Primary nozzle and drain nozzle at the left end, secondary nozzle at the right end; sum of primary nozzle free areas at least 160 in2; examples: 6 tanks need 6 primary and 6 secondary 6 in nozzles (169 in2 total), 12 tanks need 12 primary and 12 secondary 4.5 in nozzles (190 in2 total); 1 in drain nozzle; drawing marks end nozzles '4\" MIN'.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "The sum of primary nozzle free areas shall be no less than 160 in2."},
  {"n": 13, "area": "nozzles", "check": "Flanges and closures", "answer": "Furnish 900# flanges with blinds, gaskets, nuts and studs, and straight-thread O-ring sealed forged steel inlet, outlet and drain plugs. The RFP does not say which connections get flanges and which get plugs, and gives no flange facing.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Furnish 900# flanges with blinds, gaskets, nuts and studs"},
  {"n": 14, "area": "supports", "check": "Supports", "answer": "Furnish tank saddles, leg plates and leg bases to support the tank within a vertical rack; the rack is fabricated and set by others. Drawing shows a saddle near the left end and 'SUPPORT LEG: LENGTH TBD' near the right end. A drawing with typical dimensioned saddle details is required with the proposal (5.2.3).", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Furnish tank saddles, leg plates and leg bases necessary to support tank within in vertical rack"},
  {"n": 15, "area": "testing", "check": "Hydrostatic test", "answer": "Hydrotest pressure and duration per ASME; hydrostatic testing is done at the factory, before cleaning, blasting and coating (5.2.5).", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "quote": "Hydrotest pressure, duration per ASME"},
  {"n": 16, "area": "fabrication", "check": "Heat treatment / stress relief", "answer": "Referenced but not given as its own requirement: each vessel is stenciled 'STRESS RELIEVED- DO NOT WELD' in 3 in letters on opposite sides, and the exterior PT/MT examination is done 'after heat treatment' (5.3.3). No PWHT temperature or procedure is stated.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 24", "quote": "Stencil in 3” tall letters on opposite sides of vessel: “STRESS RELIEVED- DO NOT WELD”"},
  {"n": 17, "area": "testing", "check": "Non-destructive examination", "answer": "After heat treatment the exterior is examined by liquid penetrant or magnetic particle, no defects permitted; interior surfaces and welds visually examined with borescopes or fiber optics; certified NDE reports furnished. Radiography and ultrasonic extent are not stated (full text searched for radiograph, RT, UT, ultrasonic).", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 24", "quote": "After heat treatment, examine exterior of vessel by liquid penetrant or magnetic particle test, no defects permitted."},
  {"n": 18, "area": "coating", "check": "Surface preparation and coating", "answer": "After the factory hydrotest: clean to oil-free; abrasive blast interior and exterior to near white SSPC SP10/NACE No. 2; vacuum clean; black-light check for oil; 3 coats of epoxy, 8 mils minimum DFT, white finish coat inside, gray finish coat outside.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 24", "quote": "Apply 3 coats of epoxy coating 8 mils minimum dry film thickness with white finish coat for the interior"},
  {"n": 19, "area": "scope", "check": "Shipping preparation and loose items", "answer": "Purge and charge with a 5-10 psig nitrogen blanket, purge gauge on the blind flange, supported on timbers; equip with pressure gauge, drain valve and ASME VIII D1 code-stamped pressure relief valve set; one set of gaskets tagged and crated to ship loose.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 24", "quote": "Vessel to be purged and charged with a 5-10 psig nitrogen blanket and supported on timbers for shipment."},
  {"n": 20, "area": "documents", "check": "Documents", "answer": "Complete as-built drawings and full documentation on materials, welding procedures, NDE results and certifications; certified NDE reports; with the proposal, a drawing of typical dimensioned saddle details and three customer references.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 24", "quote": "Provide complete as-built drawings and full documentation on materials, welding procedures, NDE testing results and certifications."},
  {"n": 21, "area": "commercial", "check": "Delivery terms", "answer": "FOB Destination, with shipping to the University of Arizona included in the price; offloading coordinated with the University's installation contractor (to be named later); title and risk pass only when the University receives the goods (4.47).", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 24", "quote": "Include FOB Destination cost of shipping to University of Arizona."},
  {"n": 22, "area": "commercial", "check": "Warranty", "answer": "Two-year warranty on tanks; the pricing page also asks for the cost of continuing warranty beyond the initial coverage.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 24", "quote": "Warranty: provide two year warranty on tanks"},
  {"n": 23, "area": "commercial", "check": "Payment terms", "answer": "The proposer fills in a payment schedule in percent at four milestones: upon award for engineering, approved drawings, equipment fabricated ready for testing, at delivery. Terms and conditions 4.34 default to Net 30 days unless otherwise stated; credit card payment preferred; early-payment discount asked. Proposal, performance and payment bonds are not applicable.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 26", "quote": "PAYMENT SCHEDULE (%) Upon Award for engineering"},
  {"n": 24, "area": "commercial", "check": "Award criteria and schedule to quote", "answer": "Evaluation in descending order: delivery (weeks from approved shop drawings), cost of base proposal, configuration/geometry (effort to prepare the equipment yard and tank rack), manufacturer experience. Proposal gives weeks from PO to shop drawing submittal and from approved drawings to delivery.", "evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 12", "quote": "Delivery (weeks from approved shop drawings)"},
  {"n": 25, "area": "geometry", "check": "Example arrangements in the Addendum 1 drawings", "answer": "Arrangement 2a: six tanks labeled '24\" D' and '200 ft3', 6 in nozzles at both ends and 1 in drains, on an 8 in header to the wind tunnel valve station. Arrangement 2b: twelve tanks labeled '24\"', primary nozzles 4.5 in. Both also show a 'future packed bed storage vessel'.", "evidence": "L192302_Addendum_1.pdf, p. 4", "quote": "24\" D 200 ft3 [quote read from image]"}
 ],
 "contradictions": [
  {"topic": "Minimum total volume", "side_a": "Section 5.2: \"Minimum Total Capacity 1150 FT3\"; the drawing captions (RFP p. 25, Addendum pp. 4-5) also say \"1150 ft3 minimum total volume\".", "side_a_evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "side_b": "Pricing page: \"BASE PROPOSAL: minimum 1164 ft3, 2000 psig at 100 f, mdmt 0 f\".", "side_b_evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 26", "why_it_matters": "The bidder must decide whether to size the base proposal for 1150 or 1164 ft3; Addendum 1 does not resolve it ('all else remains the same').", "status": "confirmed"},
  {"topic": "Design temperature for the 2000 psig rating", "side_a": "Section 5.2: \"Design Temperature 120 F\" and \"Maximum Allowable Working Pressure 2000 PSIG at 120 F\".", "side_a_evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "side_b": "Pricing page: \"BASE PROPOSAL: minimum 1164 ft3, 2000 psig at 100 f, mdmt 0 f\".", "side_b_evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 26", "why_it_matters": "The temperature attached to the 2000 psig rating sets the allowable stress and so the wall thickness on every vessel.", "status": "confirmed"},
  {"topic": "Units of the per-tank example size", "side_a": "Section 5.2.1: \"6 tanks (200 ft2 each) requires 6 primary and 6 secondary nozzles at 6”\" (and \"12 tanks (97 ft2 each)\"), an area unit.", "side_a_evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "side_b": "Addendum drawing 2a labels each of the six tanks \"200 ft3\" (quote read from image).", "side_b_evidence": "L192302_Addendum_1.pdf, p. 4", "why_it_matters": "Almost certainly a typo for ft3 (6 x 200 = 1200, 12 x 97 = 1164 ft3), but the text literally gives an area; under 4.48 the specification governs over drawings.", "status": "confirmed"},
  {"topic": "Six-tank example versus the 50 ft length limit", "side_a": "Addendum drawing 2a labels each tank \"24\" D\" and \"200 ft3\" (quote read from image).", "side_a_evidence": "L192302_Addendum_1.pdf, p. 4", "side_b": "Section 5.2: \"Max Length Maximum length 50’\".", "side_b_evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "why_it_matters": "A 24 in diameter cylinder holding 200 ft3 is about 64 ft long, over the 50 ft limit, so the example cannot be priced as drawn; diameter drives wall thickness at 2000 psig. Marked likely because it rests on arithmetic and 'D' is not defined.", "status": "likely"},
  {"topic": "Secondary nozzle size in the twelve-tank example", "side_a": "Section 5.2.1: \"12 tanks (97 ft2 each) requires12 primary and 12 secondary nozzles at 4.5”\".", "side_a_evidence": "L192302_High_Pressure_Air_Receivers.pdf, p. 23", "side_b": "Addendum drawing 2b labels the right-end (secondary) nozzle of the fourth tank \"6\"\" while the left-end nozzles are labeled \"4.5\"\" (quote read from image; label is low resolution).", "side_b_evidence": "L192302_Addendum_1.pdf, p. 5", "why_it_matters": "Secondary nozzle size (4.5 in versus 6 in) changes nozzle, flange and blind cost on twelve vessels; 4.48 says the specification governs.", "status": "likely"}
 ]
}
