{
 "id": "us-essexjct-finescreen",
 "country": "United States",
 "language": "English",
 "buyer": "Village of Essex Junction, Vermont; engineer Aldrich + Elliott, PC",
 "project": "Water Resource Recovery Facility New Headworks Screen - Equipment Only (A + E project 17003)",
 "year": "2017",
 "files": [
  {
   "file": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf",
   "pages": 75,
   "text_layer": true,
   "what_it_is": "Single bid book: information to bidders (p. 5, scanned image), bid form and schedule of prices (pp. 7-10), contract forms, general conditions (pp. 21-25), Division 1 sections (pp. 27-53), section 11330 fine bar screen and washer compactor (pp. 55-69), drawing P1 headworks plans and section (p. 75, vector drawing with almost no text layer)"
  }
 ],
 "quality": "Short and readable, but the controls part was assembled from two maker templates (screen and compactor) that disagree on the panel enclosure, the warranty paragraph offers two clocks without saying which governs, and one cross-reference points to a section that does not exist.",
 "read_by": "Mavlon, read from the documents with AI help before any run, November 2026",
 "items": [
  "One mechanically cleaned fine bar screen (Duperon basis of design, or approved equal), 1/4 in openings, for a 2.50 ft wide channel",
  "One washer compactor with discharge chute extension (about 12 ft) and 304L stainless open channel support frame",
  "One main control panel for screen and compactor with VFDs, local NEMA 7/9 push button station(s), non-contact level control",
  "Spare parts, shop test, field service and training; equipment only (installation by a separate contractor)"
 ],
 "checks": [
  {
   "n": 1,
   "area": "scope",
   "check": "What is being bought and how is it priced?",
   "answer": "One lump sum item: the screen and washer compactor, equipment only, with all appurtenances (01025, p. 33). Section 11330 covers a mechanically cleaned fine bar screen and washer compactor in the existing headworks (p. 55).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 9",
   "quote": "Screen and Washer Compactor (Equipment only)"
  },
  {
   "n": 2,
   "area": "excluded",
   "check": "Does the supplier remove the old screen or install the new equipment?",
   "answer": "No. Removal of the existing screen and demolition are by others; installation is by a separate contractor. Field wiring between the main panel and the local station is by others (p. 63).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 27",
   "quote": "installation of this new equipment will be performed by a separate Contractor(s)."
  },
  {
   "n": 3,
   "area": "scope",
   "check": "What is the basis of design and is an equal allowed?",
   "answer": "Duperon Corporation, or approved equal; equals go through the substitution procedure of 01300 1.6 (p. 37). All equipment from a single manufacturer (p. 55).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 55",
   "quote": "shall be provided by Duperon Corporation, or approved equal."
  },
  {
   "n": 4,
   "area": "design",
   "check": "What channel and screen geometry is specified?",
   "answer": "Channel width 2.50 ft, channel height 5.25 ft, bar opening 1/4 in, installation angle 20 degrees (drawing P1 section A shows 110 degrees between the screen and the grating). Indoors, ceiling clearance 9 ft, door 6 ft-0 in, roof opening available.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 57",
   "quote": "Channel Width: 2.50 Ft Channel Height: 5.25 Ft Bar Opening Size: 1/4\" Angle of Installation: 20 degrees"
  },
  {
   "n": 5,
   "area": "design",
   "check": "What flows and water levels is the screen designed for?",
   "answer": "Average 3.3 MGD at 2 ft upstream water level; maximum 10 MGD at 4.25 ft upstream; maximum head differential 1 ft.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 57",
   "quote": "Average Flow: 3.3 MGD Average Water Level: * 2 Ft Upstream Maximum Flow: 10 MGD"
  },
  {
   "n": 6,
   "area": "electrical",
   "check": "What is the hazardous area classification?",
   "answer": "Class I Div I, local to the bar screen and washer compactor. The main control panel goes in an interior unclassified space (p. 63).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 57",
   "quote": "Installation Area Classification: Class I Div I – Local to Bar Screen and Washer Compactor"
  },
  {
   "n": 7,
   "area": "design",
   "check": "Is there a motor size rule for the screen?",
   "answer": "Yes: more than 1/2 HP or two or more motors to complete a screen cleaning cycle is not acceptable. The screen motor is 1/2 hp (p. 62); the washer compactor motor is 3/4 hp (pp. 58, 65), and the rule is worded for the screen cleaning cycle only. Single raking arms, cycle-time units, hydraulics, cables, springs and submerged sprockets are also excluded (pp. 56-57).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 57",
   "quote": "Equipment utilizing a greater than ½ HP motor or two or more motors to complete a screen cleaning cycle is not acceptable."
  },
  {
   "n": 8,
   "area": "design",
   "check": "How is the required debris removal capacity defined?",
   "answer": "0.152 ft3 per linear foot x screen width x 60 (low speed) or x 260 (high speed) x number of scrapers below water level, where scrapers below water = upstream water level / 1.745 ft.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 56",
   "quote": "Debris Volume per Linear Foot = 0.152 ft3 /hr (0.046 m3/m)"
  },
  {
   "n": 9,
   "area": "design",
   "check": "What capacity must the washer compactor have?",
   "answer": "Peak 60 cu ft/hour for about 5 minutes; average 30 cu ft/hour continuous; dual intermeshed counter-rotating augers at 2.2 RPM; accepts rocks, concrete and metal up to 4 in long.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 58",
   "quote": "Peak Capacity: 60 cu. ft/hour (for approx. 5 minutes) Average Capacity: 30 cu. ft/hour (continuous)"
  },
  {
   "n": 10,
   "area": "design",
   "check": "What wash water does the compactor need?",
   "answer": "3 to 5 gpm at 40 to 60 psi through a single 1/2 in NPT male connection (filtered effluent or municipal water); 3 in NPT male drain; 120 VAC output to a wash water solenoid from the panel (p. 66).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 58",
   "quote": "delivers 3 to 5 GPM assuming supply pressure is 40 to 60 PSI at a ½ inch NPT connection"
  },
  {
   "n": 11,
   "area": "materials",
   "check": "What are the screen bars made of?",
   "answer": "316L stainless, tear-shaped, hydraulic shape factor 0.76, minimum 0.25 x 0.75 x 0.13 in, individually replaceable without welding.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 60",
   "quote": "Bars shall be 316L stainless steel and be tear-shaped with a Hydraulic Coefficient shape factor of 0.76"
  },
  {
   "n": 12,
   "area": "materials",
   "check": "What are the other materials of construction?",
   "answer": "304 stainless unless noted: 3/16 in bent plate frame, 0.25 in dead plate, 11 ga discharge chute (p. 60), 14 ga #4 brushed 304 enclosure above deck with 16 ga removable panels (p. 61), cast 304 links and sprockets; compactor housing 304, minimum 11 ga, spur gears 17-4 PH (pp. 64-65); compactor support frame 304L (p. 67).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 60",
   "quote": "Unless noted otherwise materials of construction shall be 304 Stainless Steel."
  },
  {
   "n": 13,
   "area": "materials",
   "check": "What coating applies to non-stainless parts?",
   "answer": "SSPC-SP-10 near white blast; Tnemec three-coat: Series 90-97 zinc 2.5-3.5 mils, Series 27 F.C. Typoxy 3.0-5.0 mils, Series 1075U Endura-Shield II 2.0-3.0 mils; color 11SF Safety Blue. Same system on the compactor motor gearbox (p. 65).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 62",
   "quote": "Prime Coat Series 90-97 Tnemec Zinc at 2.5-3.5 mils DFT"
  },
  {
   "n": 14,
   "area": "electrical",
   "check": "What screen drive motor is specified?",
   "answer": "AC induction, inverter duty, 3 phase 480 V, 1/2 hp, 1800 rpm base, rated Class I Groups C & D and Class II Groups F & G, EPNV enclosure, NEMA design B, 56C frame, service factor 1.0 or greater, Class F insulation, UL listed, built-in thermostat; grease-filled gearbox, service factor 1.52 or more.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 62",
   "quote": "The motor shall be AC induction type, inverter duty, 3 phase 480 volt and mounted to the gear reducer."
  },
  {
   "n": 15,
   "area": "electrical",
   "check": "What washer compactor motor is specified?",
   "answer": "AC induction gearmotor, 3/4 hp, 3/60/230/460 V, explosion proof, inverter duty; 809:1 reducer, 0.5-2.2 RPM, 18,940 in-lb; motor service factor 1.0 (p. 58).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 65",
   "quote": "The gearmotor shall be AC induction type, ¾ hp, 3/60/230/460 volt, explosion proof, inverter duty model."
  },
  {
   "n": 16,
   "area": "controls",
   "check": "How many control panels and what limits apply?",
   "answer": "One main control panel for both screen and compactor, supplied by the manufacturer, sized for 480 V incoming with step-down to 120 V; maximum 48 in high x 36 in wide x 12 in deep; operated between 35 and 104 DegF; UL panel shop; SCCR 18 kA at 480 VAC; 20% spare terminals; tested before shipment (pp. 62-63).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 62",
   "quote": "Controls for both the screen and washer compactor shall be in a single enclosure"
  },
  {
   "n": 17,
   "area": "controls",
   "check": "What must the main panel include?",
   "answer": "Main fusible lockable disconnect, HOA, push/pull E-stop, elapsed run-time meter, Power On / Forward / fault indication; VFD, electronic torque control, hard contact SCADA interlocks, adjustable on/off cycle timers. For the compactor: vector speed controller, run/start solenoid/common fault/in auto dry contacts, remote run input, motor thermostat input (p. 66).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 63",
   "quote": "i. Variable Frequency Drive (VFD) ii. Electronic torque control iii. Hard contact SCADA Interlock(s) iv. Adjustable on/off cycle timers"
  },
  {
   "n": 18,
   "area": "controls",
   "check": "What local control station is required?",
   "answer": "NEMA 7/9 local push button station with HOA, Forward, Jog Reverse and E-Stop, within 10 ft of the equipment, field wired by the electrical subcontractor. The compactor section also requires a NEMA 7/9 remote station with the same buttons (p. 66).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 64",
   "quote": "The remote pushbutton station shall include HOA, Forward, Jog Reverse and E-Stop buttons."
  },
  {
   "n": 19,
   "area": "controls",
   "check": "How is the screen started and sped up?",
   "answer": "A separate non-contact level system per raking assembly (floats not acceptable), installed and field wired by others; two level / two speed control with off-delay timer, plus cycle timing logic in parallel. Drawing P1 shows two level transducers.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 64",
   "quote": "The level system shall be non contact as floats are not acceptable."
  },
  {
   "n": 20,
   "area": "controls",
   "check": "What signals go to plant controls from the compactor?",
   "answer": "Dry contact outputs for Run, Start Solenoid, Common Fault and In Auto; dry contact inputs for Remote Run, Motor Thermostat and remote station; Auto mode runs from a remote signal with an off-delay to clear debris.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 66",
   "quote": "Dry contact output signals for “Run”, “Start Solenoid”, “Common Fault”, and “In Auto” conditions."
  },
  {
   "n": 21,
   "area": "services",
   "check": "What spare parts and tools are required?",
   "answer": "Screen: 1 drive clevis pin, 10 snap/retaining rings, 4 link clevis pins, 4 hex head cap screws, 4 scraper nuts, 1 snap ring tool, 1 Never Seez tube. Compactor: 2 upper/lower supports, 2 side supports, 24 FHCS 0.25-20x1, 24 flat washers, 24 Nylock nuts, 1 antiseize, 1 Never Seez. One tube of multi-purpose grease (5-year supply) and a full set of panel fuses.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 67",
   "quote": "Manufacturer shall provide one tube of Multi-Purpose grease which is a 5-year supply of lubrication"
  },
  {
   "n": 22,
   "area": "scope",
   "check": "Which accessories are in the supply?",
   "answer": "Washer compactor discharge chute and extension with bends as shown, about 12 ft total with at least two bends, with supports, coordinated to field conditions; and a 304L stainless open channel support frame for the compactor spanning the existing channel.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 67",
   "quote": "The washer compactor shall be supplied with the discharge chute and extension with bends as shown on the drawing."
  },
  {
   "n": 23,
   "area": "services",
   "check": "How many field service days for installation check and testing?",
   "answer": "Not less than one 8-hour day on site to check and supervise installation and perform initial operation and acceptance tests, with a written report to the engineer. Startup services continue until the equipment passes performance testing and is accepted (p. 69), so the total is open-ended; extra time is at no cost to the owner (01731, p. 49).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 68",
   "quote": "perform the initial operation and acceptance tests for not less than one (1) 8-hour day onsite."
  },
  {
   "n": 24,
   "area": "services",
   "check": "How much operator training?",
   "answer": "At least one 8-hour day on site of instruction for the Owner's personnel (pre- and/or post-startup), separate from the installation day; written training certification required (01731, p. 51).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 69",
   "quote": "operation of the specified equipment for a minimum of one (1) 8-hour day onsite."
  },
  {
   "n": 25,
   "area": "design",
   "check": "Is a shop test required?",
   "answer": "Yes. Equipment fully assembled and shop tested at the factory with at least 4 hours run time; engineer or owner may witness. Controls tested before shipment (p. 63).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 55",
   "quote": "Shop testing shall include a minimum of 4 hours of run time."
  },
  {
   "n": 26,
   "area": "commercial",
   "check": "What warranty is required in 11330?",
   "answer": "Base: one year from substantial completion or eighteen months after delivery (the text does not say which governs) (p. 59). Plus 5 years on all rotating parts of the bar screen including gear motor, bearing, drive head and link system. Manufacturer's liability limited to cost of materials and installation; repairs may not use contract spares.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 60",
   "quote": "Manufacturer shall warrant for the period of 5 years all rotating parts of the Mechanically Cleaned Bar Screen"
  },
  {
   "n": 27,
   "area": "commercial",
   "check": "What experience is required, and what if the maker lacks it?",
   "answer": "At least 25 installations of the specified model in successful operation for at least 5 years at similar installations; otherwise a minimum 5-year warranty on the mechanical screen and washer compactor in lieu of the experience requirement.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 55",
   "quote": "a minimum five (5) year warranty shall be provided for the mechanical screen and washer compactor in lieu of the experience requirements."
  },
  {
   "n": 28,
   "area": "commercial",
   "check": "What is the delivery time and liquidated damages?",
   "answer": "Complete within 180 consecutive calendar days from the Notice to Proceed; liquidated damages $500 per consecutive calendar day (bid form p. 7; agreement p. 13).",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 7",
   "quote": "fully complete the PROJECT within 180 consecutive calendar days thereafter."
  },
  {
   "n": 29,
   "area": "commercial",
   "check": "What retainage applies?",
   "answer": "10% of each payment until final completion and acceptance, reduced to 5% after 50% of the work if progress is satisfactory, and below 5% at substantial completion to cover the punch list.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 22",
   "quote": "The OWNER shall retain ten (10) percent of the amount of each payment until final completion and acceptance"
  },
  {
   "n": 30,
   "area": "commercial",
   "check": "When are bids due and how long must they stay open?",
   "answer": "Bids due June 1, 2017 at 1:00 p.m. at the Village Office; no bidder may withdraw within 45 days of opening; no pre-bid meeting scheduled; price in words governs.",
   "evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 5 (quote read from image)",
   "quote": "No Bidder may withdraw a Bid within 45 days after the actual date of the opening."
  }
 ],
 "contradictions": [
  {
   "topic": "Main control panel enclosure: painted NEMA 12 vs NEMA 4X stainless",
   "side_a": "Enclosure(s) shall be NEMA 12, painted.",
   "side_a_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 63",
   "side_b": "N4X 304 SSTL enclosure with continuous hinge, exterior, lockable door.",
   "side_b_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 66",
   "why_it_matters": "Both describe the single main panel for screen and compactor; a 304 stainless NEMA 4X enclosure costs noticeably more than a painted NEMA 12 one.",
   "status": "confirmed"
  },
  {
   "topic": "Cross-reference to a design conditions paragraph that does not exist",
   "side_a": "unless noted otherwise in Section 2.2 J Design Conditions",
   "side_a_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 60",
   "side_b": "2.2 COMPACTOR WASHER",
   "side_b_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 64",
   "why_it_matters": "Section 2.2 is the compactor and has no item J; the design conditions (1 ft head differential) are in 1.4 A.10 on p. 57, so the bar screen design pressure must be taken from there.",
   "status": "confirmed"
  },
  {
   "topic": "Warranty clock: general conditions vs 11330",
   "side_a": "for a period of one (1) year from the date of substantial completion of the Contract.",
   "side_a_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 21",
   "side_b": "For a period of one year from the Date of Substantial Completion or eighteen months after delivery",
   "side_b_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 59",
   "why_it_matters": "Installation is by a separate contractor, so substantial completion can fall well after delivery; whether the 18-months-from-delivery cap applies changes how long the maker carries the warranty.",
   "status": "confirmed"
  },
  {
   "topic": "Number of O&M hard copies",
   "side_a": "as well as three (3) hard copy manuals.",
   "side_a_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 36",
   "side_b": "Submit two (2) paper and one (1) electronic and searchable copy draft Operation and Maintenance Manual",
   "side_b_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 47",
   "why_it_matters": "Small cost, but 01300 asks for three hard copies while 01730 and 11330 1.5 (p. 59) ask for two.",
   "status": "confirmed"
  },
  {
   "topic": "Cost of guarantee work: all costs vs liability capped",
   "side_a": "The Contractor shall bear all cost associated with such guarantee work.",
   "side_a_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 53",
   "side_b": "The manufacturer’s liability shall be limited to the cost of materials and installation.",
   "side_b_evidence": "Essex_Junction_WRRF_New_Headworks_Screen-Equip_Only.pdf, p. 60",
   "why_it_matters": "01740 puts all guarantee costs on the supplier; 11330 caps liability at materials and installation. A bidder relying on the cap may underprice warranty exposure (travel, removal, consequential costs).",
   "status": "likely"
  }
 ]
}